This patch fixes the problem, while receiving R1b type of response from the card.
In case of R1b response the continuous stream that the card sends must be checked whether the signal indicates busy status and wait until a non zero response.
The issue was found by using f_mkdir("directory_name").
The function always returned FR_DISK_ERR due to an unhadled case in sdio_write_sectors().
According to this documentation: http://www.convict.lu/pdf/ProdManualSDCardv1.9.pdf#page=92 stop transmission command should be sent after writing multiple blocks.
This patch fixes this bug also adds a test case for it.
Look-up tables were used for determining the delay loop counts before.
Based on these hand-tuned values, the loop overhead was estimated for
each option -- 80 and 160 MHz, fast and slow GPIO access. Instead of the
great number of tunable parameters one now only has to tune the overhead
values if the code is changed.
Functions were added to the API which allow setting an arbitrary
frequency. API backward compatibility is retained.
i2c: fix potential overflow situation
* The mdns responder has been reworked to lower stack and memory usage. This is
a variation on the upstream code, it use malloc whereas the upstream code uses
pools. The high stack usage of the mdns responder was problem for
esp-open-rtos, so we might have to maintain the differences for now.
* Improved lwip core locking, and lock checking. Upstream improvements, that
need some added support from esp-open-rtos specific code. More core lock is
performed when calling from the esp-open-rtos code now, so a little safer. The
checking is not enforced, but projects might see warning messages and might
want to look into them.
* The esp-open-rtos lwip support has been sync'ed with the new freertos port
included with lwip. There are still some minor differences.
* A few lwip timer bugs have been resolved. This might help resolve some issues.
* Plus it picks up all the other upstream fixes and improvements.
* The default lwip stack has been lowered from 768 words to 480 words,
due to the reduced stack usage by the mdns responder.
- GPIO_ID_PIN macros removed
- Soft reset mechanism of SHT3x does not work when sensor is in any measurement mode. Therefore, it does not abort initialization procedure anymore
- typos
- changes to use the same source code with ESP8266 (esp-open-rtos) and ESP32 (ESP-IDF)
* wificfg: remove the AP WEP mode option
The WEP mode does not appear to be implement in the sdk for the AP mode, and
defaults to open when WEP is requested which is probably not intended. Remove
the WEP option from the wifi config interface.
* lwip: enable mdns dns queries.
* wificfg: support mDNS on the softAP interface.
* Adds ipv6 support. Compiles with ipv6 enabled and then accepts ipv6
connections and answers AAAA questions.
* Fixes a few overflows of the reply buffer. Reduce the default reply buffer
size, name it MDNS_RESPONDER_REPLY_SIZE, and allow overriding.
* Fix mdns_add_TXT.
* Prefer malloc to large stack buffers, to control stack sizes, and try to
malloc only the buffer size needed where known in advance.
* Determine the IP addresses when responding, eliminating the update function
and the update task.
* Allow use in SoftAP and StationAP mode too.
* Fix to compile without the debug output.
* Slightly better integration with lwip.
* Accept a NULL TXT entry.
* Some code style changes, not comprehensive.
* When IPv6 is enabled the http server and the captive portal dns now also
accept IPv6 connections. The interface and peer IPv6 address are now also
reported.
* The http server no longer redirects <name>.local to an IP address for better
integration with mDNS.
* Add mDNS support, for the extras/mdnsresponder or the LWIP mDNS responder,
and enable the LWIP mDNS responder for examples/wificfg.
* libesphttpd: added extras and example
* Added "heatshrink" as a submodule
* Updated libesphttpd
* Updated libesphttpd
* Trying to fix the commit id
* Updated libesphttpd
* Added zlib1g-dev package
* Use native gcc to build mkespfsimage and mkupgimg
* Added NS and GW for DHCP server configuration
* Making libeshttpd up-to-date
* Making libeshttpd up-to-date (heatshrink updated)
* Making libesphttpd up-to-date
* pwm fix special state + debug print + IRAM interupt
* Special state = don't set timer, safer
* fix timer crash, cant divide by 0
* pwm dont start when duty is set
* reverse option
* fix low duty crash + comments
