Imported Upstream version 2.6.4

docs/man/oneac.txt

@@ -15,9 +15,16 @@ linkman:nutupsdrv[8].
 
 SUPPORTED HARDWARE
 ------------------
-This driver supports Oneac EG and ON UPS equipment with the
-Advanced Interface. If your UPS is equipped with the Basic
-Interface card, use the genericups driver.
+
+This driver supports various Oneac UPS families:
+
+ - EG (late 80s, early 90s, plug-in serial interface card)
+ - ON (early and mid-90s, plug-in serial interface card)
+ - OZ (mid-90s on, DB-25 std., interface slot)
+ - OB (early 2000's on, big cabinet, DB-25 std., interface slot)
+
+If your UPS is equipped with the Basic Interface card, use the
+linkman:genericups[8] driver.
 
 EXTRA ARGUMENTS
 ---------------
@@ -27,27 +34,83 @@ linkman:ups.conf[5] file:
 *testtime*='num'::
 Change battery test time from the 2 minute default.
 
+*offdelay*='num'::
+Change shutdown delay time from 0 second default.
+
 INSTANT COMMANDS
 ----------------
 This driver supports the following Instant Commands.
+(See linkman:upscmd[8])
 
-*reset.input.minmax*::
-Reset the minimum and maximum input line voltage values
-seen since the last reset or power on.
+All UPS units
+~~~~~~~~~~~~~
 
-*test.battery.start*::
-Start a battery test.  The default time is 2 minutes.  This
-time can be set in the *ups.conf* file.  See *testime* above.
+*shutdown.return*::
+Turn off the load possibly after a delay and return when power is back.
 
-*test.battery.stop*::
-Stops a battery test that is in progress.
+*shutdown.stop*::
+Stop a shutdown in progress.
+
+*shutdown.reboot*::
+Shut down the load briefly while rebooting the UPS.
 
 *test.failure.start*::
 Starts a 15 second long simulation of an input power
 failure.
 
+*test.battery.start.quick*::
+Start a "quick" battery test.  The default time is 2 minutes.  This
+time can be set in the *ups.conf* file.  See *testime* above.
+
+*test.battery.stop*::
+Stops a battery test that is in progress.
+
+All ON UPS units
+~~~~~~~~~~~~~~~~
+
+*reset.input.minmax*::
+Reset the minimum and maximum input line voltage values
+seen since the last reset or power on.
+
+Newer ON UPS units
+~~~~~~~~~~~~~~~~~~
+
+*test.panel.start*::
+Start testing the UPS panel.
+
+*test.battery.start.deep*::
+Start a "deep" battery test.  This test runs the UPS until the low
+battery point and then returns to the AC line.
+
+*reset.input.minmax*::
+Reset the minimum and maximum input line voltage values
+seen since the last reset or power on.
+
+*beeper.enable*::
+Enable UPS beeper/buzzer.
+
+*beeper.disable*::
+Disable UPS beeper/buzzer.
+
+*beeper.mute*::
+Mutes the UPS beeper/buzzer for the current alarm condition(s).
+
+Writable Variables
+------------------
+See linkman:upsrw[8] to see what variables are writable for the UPS.
+
+NOTE: If your UPS supports writing battery.runtime.low, the new set value
+is to be entered in minutes (up to 99) but the reported value is reported
+in seconds (set value * 60).
+
+NOTE: If your UPS supports input.transfer.low and input.transfer.high,
+those values are used to create an allowable output range.  The UPS 
+will do what it can to keep the output voltage value within the 
+defined range (for example: tap change or switch to inverter).
+
 AUTHOR
 ------
+Bill Elliot <bill@wreassoc.com>,
 Eric Lawson <elawson@inficad.com>
 
 SEE ALSO