When LocalDiscovery is enabled, tinc normally sends broadcast packets during
PMTU discovery to the broadcast address (255.255.255.255 or ff02::1). This
option lets tinc use a different address.
At the moment only one LocalDiscoveryAddress can be specified.
This gets rid of the rest of the symbolic links. However, as a consequence, the
crypto header files have now moved to src/, and can no longer contain
library-specific declarations. Therefore, cipher_t, digest_t, ecdh_t, ecdsa_t
and rsa_t are now all opaque types, and only pointers to those types can be
used.
Normally all requests sent via the meta connections are checked so that they
cannot be larger than the input buffer. However, when packets are forwarded via
meta connections, they are copied into a packet buffer without checking whether
it fits into it. Since the packet buffer is allocated on the stack, this in
effect allows an authenticated remote node to cause a stack overflow.
This issue was found by Martin Schobert.
Tinc never restarts PMTU discovery unless a node becomes unreachable. However,
it can be that the PMTU was very low during the initial discovery, but has
increased later. To detect this, tinc now tries to send an extra packet every
PingInterval, with a size slightly higher than the currently known PMTU. If
this packet is succesfully received back, we partially restart PMTU discovery
to find out the new maximum.
Conflicts:
src/net_packet.c
Without adding any extra traffic, we can measure round trip times, estimate the
bandwidth and packet loss between nodes. The RTT and bandwidth can be measured
by timing the MTU probe packets. The RTT is the difference between the time a
burst of MTU probes was sent and when the first reply is received. The
bandwidth can be estimated by multiplying the size of the probe packets by the
time between succesive received probe replies of the same burst. The packet
loss can be estimated for incoming traffic by comparing how many packets have
actually been received to the increase in the sequence numbers.
The estimates are not perfect. Especially bandwidth is difficult to measure,
the only accurate way is to continuously send as much data as possible, but
that is obviously not desirable. The packet loss rate is also almost always
a few percent when sending a lot of data over the VPN via TCP, since TCP
*needs* packet loss to work properly.
Keep track of the number of correct, non-replayed UDP packets that have been
received, regardless of their content. This can be compared to the sequence
number to determine the real packet loss.
There are several reasons for this:
- MacOS/X doesn't support polling the tap device using kqueue, requiring a
workaround to fall back to select().
- On Windows only sockets are properly handled, therefore tinc uses a second
thread that does a blocking ReadFile() on the TAP-Win32/64 device. However,
this does not mix well with libevent.
- Libevent, event just the core, is quite large, and although it is easy to get
and install on many platforms, it can be a burden.
- Libev is more lightweight and seems technically superior, but it doesn't
abstract away all the platform differences (for example, async events are not
supported on Windows).
We don't need to search the whole edge tree, we can use the node's own edge
tree since each edge has a pointer to its reverse. Also, we do need to make
sure we try the reflexive address often.
Before it would always use the first socket, and always send an IPv4 broadcast packet. That
works fine in a lot of situations, but it is better to try all sockets, and to send IPv6 packets
on IPv6 sockets. This is especially important for users that are on IPv6-only networks or that
have multiple physical network interfaces, although in the latter case it probably requires
them to use the ListenAddress variable to create a separate socket for each interface.
Only the very first packet of an SPTPS session should be send with REQ_KEY,
this signals the peer to abort any previous session and start a new one as
well.
The tree functions were never used on the connection_tree, a list is more appropriate.
Also be more paranoid about connections disappearing while traversing the list.
Similar to old style key exchange requests, keep track of whether a key
exchange is already in progress and how long it took. If no key is known yet
or if key exchange takes too long, (re)start a new key exchange.
When two nodes which support SPTPS want to send packets to each other, they now
always use SPTPS. The node initiating the SPTPS session send the first SPTPS
packet via an extended REQ_KEY messages. All other handshake messages are sent
using ANS_KEY messages. This ensures that intermediate nodes using an older
version of tinc can still help with NAT traversal. After the authentication
phase is over, SPTPS packets are sent via UDP, or are encapsulated in extended
REQ_KEY messages instead of PACKET messages.
When the "Broadcast = direct" option is used, broadcast packets are not sent
and forwarded via the Minimum Spanning Tree to all nodes, but are sent directly
to all nodes that can be reached in one hop.
One use for this is to allow running ad-hoc routing protocols, such as OLSR, on
top of tinc.
This allows tincctl to receive log messages from a running tincd,
independent of what is logged to syslog or to file. Tincctl can receive
debug messages with an arbitrary level.
