There are two caveats to be aware of which are documented in this
commit:
- Because the system will likely assign different ports when binding
several times to different address families, it is recommended to
only use a single address family, otherwise other nodes will only
get one port among the several that were assigned, possibly breaking
communication.
- AutoConnect won't work in this scenario, because it relies on the UDP
port being the same as the TCP port, which is not the case when using
system-assigned ports.
This adds a new option, BroadcastSubnet, that allows the user to
declare broadcast subnets, i.e. subnets which are considered broadcast
addresses by the tinc routing layer. Previously only the global IPv4
and IPv6 broadcast addresses were supported by virtue of being
hardcoded.
This is useful when using tinc in router mode with Ethernet virtual
devices, as it can be used to provide broadcast support for a local
broadcast address (e.g. 10.42.255.255) instead of just the global
address (255.255.255.255).
This is implemented by removing hardcoded broadcast addresses and
introducing "broadcast subnets", which are subnets with a NULL owner.
By default, behavior is unchanged; this is accomplished by adding
the global broadcast addresses for Ethernet, IPv4 and IPv6 at start
time.
Recent improvements to the local discovery mechanism makes it cheaper,
more network-friendly, and now it cannot make things worse (as opposed
to the old mechanism). Thus there is no reason not to enable it by
default.
The new local address based local discovery mechanism is technically
superior to the old broadcast-based one. In fact, the old algorithm
can technically make things worse by e.g. sending broadcasts over the
VPN itself and then selecting the VPN address as the node's UDP
address. This cannot happen with the new mechanism.
Note that this means old nodes that don't send their local addresses in
ADD_EDGE messages can't be discovered, because there is no address to
send discovery packets to. Old nodes can still discover new nodes by
sending them broadcasts, though.
This introduces a new way of doing local discovery: when tinc has
local address information for the recipient node, it will send local
discovery packets directly to the local address of that node, instead
of using broadcast packets.
This new way of doing local discovery provides numerous advantages compared to
using broadcasts:
- No broadcast packets "polluting" the local network;
- Reliable even if the sending host has multiple network interfaces (in
contrast, broadcasts will only be sent through one unpredictable
interface)
- Works even if the two hosts are not on the same broadcast domain. One
example is a large LAN where the two hosts might be on different local
subnets. In fact, thanks to UDP hole punching this might even work if
there is a NAT sitting in the middle of the LAN between the two nodes!
- Sometimes a node is reachable through its "normal" address, and via a
local subnet as well. One might think the local subnet is the best route
to the node in this case, but more often than not it's actually worse -
one example is where the local segment is a third party VPN running in
parallel, or ironically it can be the local segment formed by the tinc
VPN itself! Because this new algorithm only checks the addresses for
which an edge is already established, it is less likely to fall into
these traps.
Besides controlling when tinc-up and tinc-down get called, this commit makes
DeviceStandby control when the virtual network interface "cable" is "plugged"
on Windows. This is more user-friendly as the status of the tinc network can
be seen just by looking at the state of the network interface, and it makes
Windows behave better when isolated.
This adds a new DeviceStandby option; when it is disabled (the default),
behavior is unchanged. If it is enabled, tinc-up will not be called during
tinc initialization, but will instead be deferred until the first node is
reachable, and it will be closed as soon as no nodes are reachable.
This is useful because it means the device won't be set up until we are fairly
sure there is something listening on the other side. This is more user-friendly,
as one can check on the status of the tinc network connection just by checking
the status of the network interface. Besides, it prevents the OS from thinking
it is connected to some network when it is in fact completely isolated.
ListenAddress works the same as BindToAddress, except that from now on,
explicitly binding outgoing packets to the address of a socket is only done for
sockets specified with BindToAddress.
According to Debian, texi2html is deprecated and makeinfo --html should be used
instead. Automake already provides a html target that invokes makeinfo.
Tinc now strictly limits incoming connections from the same host to 1 per
second. For incoming connections from multiple hosts short bursts of incoming
connections are allowed (by default 100), but on average also only 1 connection
per second is allowed.
When an incoming connection exceeds the limit, tinc will keep the connection in
a tarpit; the connection will be kept open but it is ignored completely. Only
one connection is in a tarpit at a time to limit the number of useless open
connections.
When LocalDiscovery is enabled, tinc normally sends broadcast packets during
PMTU discovery to the broadcast address (255.255.255.255 or ff02::1). This
option lets tinc use a different address.
At the moment only one LocalDiscoveryAddress can be specified.
Using the tinc command, an administrator of an existing VPN can generate
invitations for new nodes. The invitation is a small URL that can easily
be copy&pasted into email or live chat. Another person can have tinc
automatically setup the necessary configuration files and exchange keys
with the server, by only using the invitation URL.
The invitation protocol uses temporary ECDSA keys. The invitation URL
consists of the hostname and port of the server, a hash of the server's
temporary ECDSA key and a cookie. When the client wants to accept an
invitation, it also creates a temporary ECDSA key, connects to the server
and says it wants to accept an invitation. Both sides exchange their
temporary keys. The client verifies that the server's key matches the hash
in the invitation URL. After setting up an SPTPS connection using the
temporary keys, the client gives the cookie to the server. If the cookie
is valid, the server sends the client an invitation file containing the
client's new name and a copy of the server's host config file. If everything
is ok, the client will generate a long-term ECDSA key and send it to the
server, which will add it to a new host config file for the client.
The invitation protocol currently allows multiple host config files to be
send from the server to the client. However, the client filters out
most configuration variables for its own host configuration file. In
particular, it only accepts Name, Mode, Broadcast, ConnectTo, Subnet and
AutoConnect. Also, at the moment no tinc-up script is generated.
When an invitation has succesfully been accepted, the client needs to start
the tinc daemon manually.
There are several reasons for this:
- MacOS/X doesn't support polling the tap device using kqueue, requiring a
workaround to fall back to select().
- On Windows only sockets are properly handled, therefore tinc uses a second
thread that does a blocking ReadFile() on the TAP-Win32/64 device. However,
this does not mix well with libevent.
- Libevent, event just the core, is quite large, and although it is easy to get
and install on many platforms, it can be a burden.
- Libev is more lightweight and seems technically superior, but it doesn't
abstract away all the platform differences (for example, async events are not
supported on Windows).
