Updates, updates

doc/tinc.texi

@@ -1,5 +1,5 @@
 \input texinfo   @c -*-texinfo-*-
-@c $Id: tinc.texi,v 1.8.4.6 2000/11/02 21:34:45 zarq Exp $
+@c $Id: tinc.texi,v 1.8.4.7 2000/11/09 21:29:58 zarq Exp $
 @c %**start of header
 @setfilename tinc.info
 @settitle tinc Manual
@@ -17,7 +17,7 @@ Copyright @copyright{} 1998,199,2000 Ivo Timmermans
 <itimmermans@@bigfoot.com>, Guus Sliepen <guus@@sliepen.warande.net> and
 Wessel Dankers <wsl@@nl.linux.org>.
 
-$Id: tinc.texi,v 1.8.4.6 2000/11/02 21:34:45 zarq Exp $
+$Id: tinc.texi,v 1.8.4.7 2000/11/09 21:29:58 zarq Exp $
 
 Permission is granted to make and distribute verbatim copies of this
 manual provided the copyright notice and this permission notice are
@@ -42,7 +42,7 @@ Copyright @copyright{} 1998,1999,2000 Ivo Timmermans
 <itimmermans@@bigfoot.com>, Guus Sliepen <guus@@sliepen.warande.net> and
 Wessel Dankers <wsl@@nl.linux.org>.
 
-$Id: tinc.texi,v 1.8.4.6 2000/11/02 21:34:45 zarq Exp $
+$Id: tinc.texi,v 1.8.4.7 2000/11/09 21:29:58 zarq Exp $
 
 Permission is granted to make and distribute verbatim copies of this
 manual provided the copyright notice and this permission notice are
@@ -532,35 +532,14 @@ The actual setup of the ethertap device is quite simple, just repeat
 after me:
 
 @example
-ifconfig tap@emph{n} hw ether fe:fd:@emph{xx}:@emph{xx}:@emph{xx}:@emph{xx}
+ifconfig tap@emph{n} hw ether fe:fd:00:00:00:00
 @end example
 
-The @emph{n} here is the number of the ethertap device you want to use.
-It should be the same @emph{n} as the one you use for
-@file{/dev/tap@emph{n}}.  The @emph{xx}s are four hexadecimal numbers
-(0--ff). With previous versions of tincd, it didn't matter what they
-were.  But newer kernels require properly set up ethernet addresses.  In
-fact, the old behavior was wrong.  It is required that the @emph{xx}s
-match the numbers of the IP address you will give to the tap device and
-to the MyOwnVPNIP configuration (which will be discussed later).
-
 @cindex MAC address
 @cindex hardware address
-@strong{Tip}: for finding out what the MAC address of the tap interface
+@strong{Note:} Since version 1.0pre3, all interface addresses are set to
-should be, you can use the following command:
+this address, whereas previous versions required the MAC to match the
-
+actual IP address.
-@example
-$ printf 'fe:fd:%02x:%02x:%02x:%02x' 10 1 54 1
-fe:fd:0a:01:36:01
-@end example
-
-or with perl:
-
-@example
-$ perl -e 'print "fe:fd:", join(":", map @{sprintf "%02x", $_@} split(/\./, $ARGV[0])), "\n";' 10.1.54.1
-fe:fd:0a:01:36:01
-@end example
-
 
 @cindex ifconfig
 To activate the device, you have to assign an IP address to it.  To set
@@ -741,17 +720,20 @@ maskbits is the number of bits set to 1 in the netmask part.
 @item MyVirtualIP = <local address[/maskbits]>
 This is an alias for MyOwnVPNIP.
 
-@item Passphrases = <directory> (/etc/tinc/NETNAME/passphrases)
-The directory where tinc will look for passphrases when someone tries to
-connect. Please see the manpage for genauth(8) for more information
-about passphrases as used by tinc.
-
 @item PingTimeout = <seconds> (5)
 The number of seconds of inactivity that tinc will wait before sending a
 probe to the other end. If that other end doesn't answer within that
 same amount of seconds, the connection is terminated, and the others
 will be notified of this.
 
+@item PrivateKey = <key>
+This is a sequence of hexadecimal numbers, as generated by ``tincd
+--generate-keys''.
+
+@item PublicKey = <key>
+This is a sequence of hexadecimal numbers, as generated by ``tincd
+--generate-keys''.
+
 @item TapDevice = <device> (/dev/tap0)
 The ethertap device to use. Note that you can only use one device per
 daemon. The info pages of the tinc package contain more information