/******************************************************************************
 *
 * Copyright(c) 2007 - 2011 Realtek Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of version 2 of the GNU General Public License as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along with
 * this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
 *
 *
 ******************************************************************************/
#ifndef REALTEK_POWER_SEQUENCE_8195A
#define REALTEK_POWER_SEQUENCE_8195A

#include "HalPwrSeqCmd.h"

/* 
	Check document WM-20130111-JackieLau-RTL8723B_Power_Architecture v02.vsd
	There are 6 HW Power States:
	0: POFF--Power Off
	1: PDN--Power Down
	2: CARDEMU--Card Emulation
	3: ACT--Active Mode
	4: LPS--Low Power State
	5: SUS--Suspend

	The transision from different states are defined below
	TRANS_CARDEMU_TO_ACT
	TRANS_ACT_TO_CARDEMU
	TRANS_CARDEMU_TO_SUS
	TRANS_SUS_TO_CARDEMU
	TRANS_CARDEMU_TO_PDN
	TRANS_ACT_TO_LPS
	TRANS_LPS_TO_ACT	

	TRANS_END
*/
#define	RTL8195A_TRANS_CARDEMU_TO_ACT_STEPS	4
#define	RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS	4
#define	RTL8195A_TRANS_CARDEMU_TO_SUS_STEPS	7
#define	RTL8195A_TRANS_SUS_TO_CARDEMU_STEPS	15
#define	RTL8195A_TRANS_CARDEMU_TO_PDN_STEPS	15
#define	RTL8195A_TRANS_PDN_TO_CARDEMU_STEPS	15
#define	RTL8195A_TRANS_ACT_TO_LPS_STEPS		15
#define	RTL8195A_TRANS_LPS_TO_ACT_STEPS		15	
#define	RTL8195A_TRANS_ACT_TO_SWLPS_STEPS		22
#define	RTL8195A_TRANS_SWLPS_TO_ACT_STEPS		15
#define	RTL8195A_TRANS_END_STEPS		1
//1TODO:chris
#if 1
#define RTL8195A_TRANS_CARDEMU_TO_ACT 														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/   \
	{0x0004, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},\
	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},\
	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/	


#define RTL8195A_TRANS_ACT_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT0|BIT1|BIT2), 0},/*0x04[24:26] = 0 turn off RF*/	\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT0|BIT1), 0},/*0x04[16:17] = 0 BB reset*/	\
	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x20[1] = 1 turn off MAC by HW state machine*/	\
	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x20[1] = 0 polling until return 0 to disable*/	\

#define RTL8195A_TRANS_CARDEMU_TO_SUS													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/	\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/   \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/

#define RTL8195A_TRANS_SUS_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/

#define RTL8195A_TRANS_CARDEMU_TO_CARDDIS													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\

#define RTL8195A_TRANS_CARDDIS_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\


#define RTL8195A_TRANS_CARDEMU_TO_PDN												\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/

#define RTL8195A_TRANS_PDN_TO_CARDEMU												\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/

#define RTL8195A_TRANS_ACT_TO_LPS														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/	\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/	\
	{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/	\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/	\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/	\
	{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/	\
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/	


#define RTL8195A_TRANS_LPS_TO_ACT															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
	{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
	{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*.	0x08[4] = 0		 switch TSF to 40M*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/\
	{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.	0x29[7:6] = 2b'00	 enable BB clock*/\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1*/\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/
 
 
 #define RTL8195A_TRANS_ACT_TO_SWLPS														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*enable 32 K source*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/	\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*disable security engine*/	\
	{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x40},/*When driver enter Sus/ Disable, enable LOP for BT*/	\
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*reset dual TSF*/	\
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/*Reset CPU*/	\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*Reset MCUFWDL register*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*Reset CPU IO Wrapper*/	\
	{0x0287, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*polling RXFF packet number = 0 */	\
	{0x0286, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/*polling RXDMA idle */	\
	{0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Clear FW RPWM interrupt */\
	{0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Set FW RPWM interrupt source*/\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4},/*switch TSF to 32K*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/*polling TSF stable*/\
	{0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Set FW LPS*/	\
	{0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/*polling FW LPS ready */


#define RTL8195A_TRANS_SWLPS_TO_ACT															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0},/*switch TSF to 32K*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1, enable security engine*/\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/\
	{0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x09}, /*.	reset MAC rx state machine*/\
	{0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x86}, /*.	reset MAC rx state machine*/\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/	\
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/	\
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/	\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */	\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/

 

#else

#define RTL8723B_TRANS_CARDEMU_TO_ACT 														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/   \
	{0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x67[0] = 0 to disable BT_GPS_SEL pins*/	\
	{0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS},/*Delay 1ms*/   \
	{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, 0}, /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/   \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* disable SW LPS 0x04[10]=0*/	\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/* wait till 0x04[17] = 1    power ready*/	\
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* release WLON reset  0x04[16]=1*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* disable HWPDN 0x04[15]=0*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, (BIT4|BIT3), 0},/* disable WL suspend*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/* polling until return 0*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/**/	\
	{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/* Enable WL control XTAL setting*/	\
	{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable falling edge triggering interrupt*/\
	{0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable GPIO9 interrupt mode*/\
	{0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable GPIO9 input mode*/\
	{0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Enable HSISR GPIO[C:0] interrupt*/\
	{0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/*Enable HSISR GPIO9 interrupt*/\
	{0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3, BIT3},/*For GPIO9 internal pull high setting by test chip*/\
	{0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, BIT6},/*For GPIO9 internal pull high setting*/

#define RTL8723B_TRANS_ACT_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*0x1F[7:0] = 0 turn off RF*/	\
	{0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*0x4C[24] = 0x4F[0] = 0, switch DPDT_SEL_P output from register 0x65[2] */\
	{0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Enable rising edge triggering interrupt*/ \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*0x04[9] = 1 turn off MAC by HW state machine*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, 0}, /*wait till 0x04[9] = 0 polling until return 0 to disable*/	\
	{0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6, 0},/* Enable BT control XTAL setting*/	\
	{0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5}, /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/   \
	{0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/   \


#define RTL8723B_TRANS_CARDEMU_TO_SUS													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4|BIT3, (BIT4|BIT3)}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/	\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/   \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3|BIT4}, /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/

#define RTL8723B_TRANS_SUS_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/

#define RTL8723B_TRANS_CARDEMU_TO_CARDDIS													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07=0x20 , SOP option to disable BG/MB*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, BIT3}, /*0x04[12:11] = 2b'01 enable WL suspend*/	\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2}, /*0x04[10] = 1, enable SW LPS*/	\
        {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1}, /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/   \
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, BIT0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, 0}, /*wait power state to suspend*/

#define RTL8723B_TRANS_CARDDIS_TO_CARDEMU													\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3 | BIT7, 0}, /*clear suspend enable and power down enable*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, BIT0, 0}, /*Set SDIO suspend local register*/	\
	{0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_POLLING, BIT1, BIT1}, /*wait power state to suspend*/\
        {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0}, /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/   \
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT3|BIT4, 0}, /*0x04[12:11] = 2b'01enable WL suspend*/\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*0x23[4] = 1b'0 12H LDO enter normal mode*/   \
	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*PCIe DMA start*/


#define RTL8723B_TRANS_CARDEMU_TO_PDN												\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4}, /*0x23[4] = 1b'1 12H LDO enter sleep mode*/   \
	{0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK|PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x20}, /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/   \
	{0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/* 0x04[16] = 0*/\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/* 0x04[15] = 1*/

#define RTL8723B_TRANS_PDN_TO_CARDEMU												\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/* 0x04[15] = 0*/

#define RTL8723B_TRANS_ACT_TO_LPS														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*PCIe DMA stop*/	\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF},/*Tx Pause*/	\
	{0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*Should be zero if no packet is transmitting*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US},/*Delay 1us*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*Whole BB is reset*/	\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x03},/*Reset MAC TRX*/	\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*check if removed later*/	\
	{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x00},/*When driver enter Sus/ Disable, enable LOP for BT*/	\
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*Respond TxOK to scheduler*/	


#define RTL8723B_TRANS_LPS_TO_ACT															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_SDIO,PWR_CMD_WRITE, 0xFF, 0x84}, /*SDIO RPWM*/\
	{0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*USB RPWM*/\
	{0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x84}, /*PCIe RPWM*/\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, /*Delay*/\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0}, /*.	0x08[4] = 0		 switch TSF to 40M*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, 0}, /*Polling 0x109[7]=0  TSF in 40M*/\
	{0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT6|BIT7, 0}, /*.	0x29[7:6] = 2b'00	 enable BB clock*/\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1*/\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1|BIT0, BIT1|BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/
 
 
 #define RTL8723B_TRANS_ACT_TO_SWLPS														\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0194, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*enable 32 K source*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*CCK and OFDM are enable*/	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*CCK and OFDM are disabled,and clock are gated*/	\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x3F},/*Reset MAC TRX*/	\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, 0},/*disable security engine*/	\
	{0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x40},/*When driver enter Sus/ Disable, enable LOP for BT*/	\
	{0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT5, BIT5},/*reset dual TSF*/	\
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/*Reset CPU*/	\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0},/*Reset MCUFWDL register*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 1},/*Reset CPU IO Wrapper*/	\
	{0x0287, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, 0xFF, 0},/*polling RXFF packet number = 0 */	\
	{0x0286, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT1, BIT1},/*polling RXDMA idle */	\
	{0x013D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Clear FW RPWM interrupt */\
	{0x0139, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Set FW RPWM interrupt source*/\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, BIT4},/*switch TSF to 32K*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, BIT7},/*polling TSF stable*/\
	{0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*Set FW LPS*/	\
	{0x0090, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT0, 0},/*polling FW LPS ready */	


#define RTL8723B_TRANS_SWLPS_TO_ACT															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT4, 0},/*switch TSF to 32K*/\
	{0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT7, 0},/*polling TSF stable*/\
	{0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1}, /*.	0x101[1] = 1, enable security engine*/\
	{0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0xFF}, /*.	0x100[7:0] = 0xFF	 enable WMAC TRX*/\
	{0x06B7, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x09}, /*.	reset MAC rx state machine*/\
	{0x06B4, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0x86}, /*.	reset MAC rx state machine*/\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT1, BIT1},/* set CPU RAM code ready*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, 0},/*Reset CPU IO Wrapper*/	\
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, 0},/* Enable CPU*/	\
	{0x001D, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0},/*enable CPU IO Wrapper*/	\
	{0x0003, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT2, BIT2},/* Enable CPU*/	\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT7, BIT7},/*polling FW init ready */	\
	{0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_POLLING, BIT6, BIT6},/*polling FW init ready */	\
	{0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, BIT0, BIT0}, /*.	0x02[1:0] = 2b'11	 enable BB macro*/\
	{0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK,PWR_BASEADDR_MAC,PWR_CMD_WRITE, 0xFF, 0}, /*.	0x522 = 0*/

        
#endif


	
#define RTL8195A_TRANS_END															\
	/* format */																\
	/* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, // comments here*/								\
	{0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,0,PWR_CMD_END, 0, 0}, //


extern WLAN_PWR_CFG rtl8195A_power_on_flow[RTL8195A_TRANS_CARDEMU_TO_ACT_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_radio_off_flow[RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_card_disable_flow[RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8195A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_card_enable_flow[RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8195A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_suspend_flow[RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8195A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_resume_flow[RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8195A_TRANS_CARDEMU_TO_SUS_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_hwpdn_flow[RTL8195A_TRANS_ACT_TO_CARDEMU_STEPS+RTL8195A_TRANS_CARDEMU_TO_PDN_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_enter_lps_flow[RTL8195A_TRANS_ACT_TO_LPS_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_leave_lps_flow[RTL8195A_TRANS_LPS_TO_ACT_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_enter_swlps_flow[RTL8195A_TRANS_ACT_TO_SWLPS_STEPS+RTL8195A_TRANS_END_STEPS];
extern WLAN_PWR_CFG rtl8195A_leave_swlps_flow[RTL8195A_TRANS_SWLPS_TO_ACT_STEPS+RTL8195A_TRANS_END_STEPS];
#endif

