RTL00_HelloWorld/openocd/rtl_gdb_flash_write_openocd.txt

# GDB script for loading ram.bin process

#===============================================================================
#set GDB connection 
set remotetimeout 100000
target remote :10000

#===============================================================================
#set file path
set $BINFILE = "./application/Debug/bin/ram_all.bin"

#===============================================================================
#Message display setting
#disable all messages

set verbose off
set complaints 0
set confirm off
set exec-done-display off
show exec-done-display
set trace-commands off
#set debug aix-thread off
#set debug dwarf2-die 0
set debug displaced off 
set debug expression 0
set debug frame 0
set debug infrun 0
set debug observer 0
set debug overload 0
set debugvarobj 0
set pagination off
set print address off
set print symbol-filename off
set print symbol off
set print pretty off
set print object off
#set debug notification off
set debug parser off
set debug remote 0

#===============================================================================
#set JTAG and external SRAM
monitor reset init
monitor halt
monitor sleep 20
#===============================================================================
#Variables declaration (1)
#binary file size
set $RamFileSize = 0x0000
source fwsize.gdb
printf "-------------------------------\n"
printf "RamFileSize: %x\n",$RamFileSize
printf "-------------------------------\n"

#===============================================================================
set $FLASHDATBUFSIZE = 0x800

#===============================================================================
#define PERI_ON_BASE 0x40000000
set $PERI_ON_BASE = 0x40000000
#define REG_SOC_PERI_FUNC0_EN 0x0218
set $REG_SOC_PERI_FUNC0_EN = 0x0210

#define SPI_FLASH_BASE 0x4000000
set $SPI_FLASH_BASE = 0x98000000

#------------------------------------------------------------------
set $Temp = 0x0

#===============================================================================
#Load flash download file
file ../../../component/soc/realtek/8195a/misc/gcc_utility/target_NORMAL.axf

#Load the file
lo

printf "Load flash controller.\n"
#===============================================================================
#Set for executing flash controller funciton
set $Temp = {int}($PERI_ON_BASE+$REG_SOC_PERI_FUNC0_EN)
p /x $Temp

set $Temp = ($Temp | (0x01 << 27))
p /x $Temp

set {int}($PERI_ON_BASE+$REG_SOC_PERI_FUNC0_EN) = $Temp
printf "....\n"
printf "wakeup bit(%x):%x\n", ($PERI_ON_BASE+$REG_SOC_PERI_FUNC0_EN), {int}($PERI_ON_BASE+$REG_SOC_PERI_FUNC0_EN)
#===============================================================================
#Direct the startup wake function to  flash program function
#the function pointer address
#set $testpointer = 0x200006b4
#set $testpointer2 = 0x200006b8
#set $FuntionPointer = 0x200006c4
#set $FPTemp = 0x200a08e9
#set {int}($FuntionPointer) = $FPTemp
#printf "testpointer(%x):%x\n", $testpointer, {int}$testpointer
#printf "testpointer2(%x):%x\n", $testpointer2, {int}$testpointer2
#printf "FuntionPointer(%x):%x\n", $FuntionPointer, {int}$FuntionPointer 

#===============================================================================
#Load file
#    restore filename [binary] bias start end
#	Restore the contents of file filename into memory. 
#	The restore command can automatically recognize any known bfd file format, except for raw binary. 
#	To restore a raw binary file you must specify the optional keyword binary after the filename.
#=============================================================================== 
                                                  
set $LoopNum = ($RamFileSize / $FLASHDATBUFSIZE)
printf "LoopNum = %x\n", $LoopNum
set $TailSize = ($RamFileSize % $FLASHDATBUFSIZE)
printf "TailSize = %x\n", $TailSize

printf "global variables\n"

set $FLASHDATSRC = 0x0
set $FILESTARTADDR = 0X0
set $FILEENDADDR = $FILESTARTADDR + $FLASHDATBUFSIZE

#b RtlFlashProgram:StartOfFlashBlockWrite
b rtl_flash_download.c:489
b rtl_flash_download.c:524
#b Rtl_flash_control.c:RtlFlashProgram

#continue to 489
c

# Mode 0: erase full chip, Mode 1: skip calibration section and erase to firmware size
set EraseMode=1
print EraseMode
set FirmwareSize=$RamFileSize
print FirmwareSize

#continue to 524
c

#printf "...\n"
set $FLASHDATSRC = FlashDatSrc
printf "FlashDatSrc:%x\n", $FLASHDATSRC
                     
printf  "FlashBlockWriteSize "
set FlashBlockWriteSize = $FLASHDATBUFSIZE
#p /x FlashBlockWriteSize
printf "FlashBlockWriteSize:%x\n", FlashBlockWriteSize

printf  "FlashAddrForWrite" 
set FlashAddrForWrite = 0x0



printf  "Flash write start...\n"
set $LoopCnt = 0
while  ($LoopCnt < $LoopNum)
	p /x FlashAddrForWrite
    restore ./application/Debug/bin/ram_all.bin binary ($FLASHDATSRC-$FILESTARTADDR) $FILESTARTADDR $FILEENDADDR
    c
    
    printf "FILEENDADDR"
    p /x $FILEENDADDR
    set FlashBlockWriteSize = $FLASHDATBUFSIZE
    set FlashAddrForWrite = $FILEENDADDR
    set $FILESTARTADDR = $FILEENDADDR
    set $FILEENDADDR = $FILESTARTADDR + $FLASHDATBUFSIZE   
    
    set $LoopCnt = $LoopCnt + 0x01
end

#set FlashBlockWriteSize = $FLASHDATBUFSIZE
#set FlashAddrForWrite = $FILEENDADDR
#set $FILESTARTADDR = $FILEENDADDR
set $FILEENDADDR = $FILESTARTADDR + $TailSize
restore ./application/Debug/bin/ram_all.bin binary ($FLASHDATSRC-$FILESTARTADDR) $FILESTARTADDR $FILEENDADDR
c

#Set complete flas
set FlashWriteComplete = 0x1

printf "dump for check\n"

set $LoopCnt = 0
set $dumpaddr = 0

set $dumpstartaddr = $SPI_FLASH_BASE
set $dumpendaddr = $SPI_FLASH_BASE + $RamFileSize
printf "start addr of dumping"
p /x $dumpstartaddr
printf "end addr of dumping"
p /x $dumpendaddr 
dump binary memory  ./application/Debug/bin/dump.bin $dumpstartaddr $dumpendaddr


delete
b rtl_flash_download.c:556
c

quit
#===============================================================================